Basement Insulation in Toronto, ON
We find out what the wall is made of and check that it stays dry. Then we insulate it with closed-cell spray foam or rigid foam board.
Basement insulation in Toronto starts with two facts about the wall: what it is made of and whether it stays dry. We check both before we suggest closed-cell spray foam or rigid foam board, and the work itself starts at the rim joists. It makes sense if you're finishing a basement, or if the floor upstairs is cold.
Water first, insulation second
Only insulate a basement wall once it has shown it stays dry. Foam and board slow heat loss, but they do nothing about water. Put insulation over a wet wall and you hide the problem while holding moisture against the masonry, where it can rot framing and feed mould behind the finished wall.
Before any basement insulation in Toronto, go down after a heavy rain or a spring thaw and look for these signs:
- Tide lines or dark stains low on the wall or along the floor.
- A white, powdery crust on brick, stone or concrete block. That's efflorescence, the salt water leaves behind as it moves through the masonry and dries off the surface.
- Damp patches that appear with rain or snowmelt and fade when the weather is dry.
- A musty smell, peeling paint, or rust at the base of steel posts and on nails near the floor.
- Water along the joint where the floor meets the wall.
- Downspouts emptying right beside the house, or ground sloping toward the foundation.
A simple check you can do yourself
Tape a square of clear plastic tight to the bare wall and leave it for a few days. If moisture shows up under the plastic, water is coming through the wall. If it's on top, humid basement air is condensing on a cold surface, and a dehumidifier will help with that. Water coming through means your next call is to a waterproofing contractor. We don't do waterproofing, drainage or foundation repair. Once the wall has stayed dry through a wet season, we can come back and insulate it.
What your foundation walls are made of
What your foundation walls are made of decides what insulation they can take. A lot of our work at Premier Insulation Toronto is in Victorian and Edwardian semis in the west end, so older masonry is a big part of the job. Rough stone and flat concrete need different methods.
Brick and stone
Brick and rubble stone foundations have rough, uneven faces, soft mortar joints and hollows big enough to fit a hand in. Closed-cell spray foam suits them best because it follows every bump and seals the gaps a flat board would leave. If the mortar is crumbling or the wall is still damp, a mason or waterproofing contractor has to deal with that first.
Concrete block
Concrete block walls have hollow cores that can carry air and moisture up and down the wall. The open cores along the top course need sealing so cold air doesn't rise into the framing. Most block walls are flat enough for rigid foam board with taped joints. If the block has shifted or bowed, spraying is better, since foam fills the gaps a board would only bridge.
Poured concrete
Poured concrete is the flattest, most even foundation wall, and rigid foam board works well against it. Check the form-tie holes and any cracks for seepage first, because that's where small leaks tend to get in. Once the wall is dry, board glued tight to it with sealed edges gives you one clean, continuous layer.
Closed-cell foam or rigid board
Closed-cell spray foam suits rough, uneven masonry, and rigid foam board suits flat walls. Foam goes on as a liquid, expands and bonds to the brick or stone, so it makes its own air seal and leaves nothing behind it open to warm, moist basement air. That's why a spray foam basement wall works well on old foundations.
Rigid foam board goes on in sheets, glued or fastened to the wall. It only works if every joint is taped and the top and bottom edges are sealed with foam or sealant. On an uneven wall, air can slip behind the board, hit the cold masonry and condense there. On a flat, dry wall with careful sealing, board does the job well.
Either way, a stud wall usually goes in front to carry the drywall and outlets. Our closed-cell spray foam page goes into the material in more detail.
Vapour barriers in a basement
A low-permeance vapour barrier on the inside of insulated masonry can do harm, because it stops the wall drying inward. Moisture from the soil moves through brick, stone and block all the time. Put plastic sheeting on the room side and that moisture gets trapped in the wall and in any batts beside it.
Closed-cell foam already controls vapour, so we don't add plastic sheeting over it by default. Board walls need taped seams and sealed edges, and whether they need more vapour control depends on the wall itself. Older finishing jobs often got this part of a vapour barrier basement plan wrong: batts against the wall, poly on the face, and damp insulation stuck in between.
Rim joists: where we usually start
Where the floor joists end on the foundation, a board caps them off: the rim joist, often the leakiest part of a basement. Air gets in at the sill plate, between the boards, and around every pipe, wire and dryer vent that passes through. We seal this band before we start on the basement wall insulation below it. A well-insulated wall loses much of its value if the rim above it is still drafty.
Rim Joist Insulation
We spray closed-cell foam into each joist bay, which seals the air leaks and insulates the framing in a single layer. Our rim joist insulation page covers how the job goes and what to look for. If the floor upstairs is cold, this is often the first thing to fix.
What SB-12 asks of a new basement
For a new house in Zone 1, SB-12 sets R-20 of continuous insulation as the minimum for basement walls in compliance packages A1, A3, A4 and A6. SB-12 is the energy efficiency standard for houses in Ontario's building code. Continuous means studs don't break the layer, which is why foam on the masonry with a stud wall in front works well.
For an existing basement, SB-12 is a reference point rather than a requirement. We use it as a benchmark when we talk about how much to add, and weigh it against how much headroom and floor space you're willing to give up.
Permits and rebates for basement work
Finishing a basement needs no City of Toronto building permit when the work makes no structural or material changes, adds no new dwelling unit and puts in no new plumbing. Adding insulation on its own needs no permit. A new bathroom, a second suite or moving a structural wall is different, so check with the City before starting those.
On the home energy assessment route, Home Renovation Savings may cover foundation insulation. That route has its own order of steps, so read the program's current steps and amounts on its website before work begins.
FAQ
Common questions about basement insulation
Closed-cell spray foam is the best fit for brick, stone and uneven block, and rigid foam board works well on flat poured concrete or straight block. Which one depends on what the wall is made of and whether it stays dry. We don't put fibreglass batts directly against bare masonry, because they hold moisture against the wall.
You usually don't need a separate vapour barrier on a masonry basement wall insulated with closed-cell spray foam, because the foam already controls vapour. A low-permeance plastic sheet on the inside of insulated masonry can stop the wall drying inward and trap moisture. We decide on vapour control by looking at the wall type and the insulation going on it.
Yes, closed-cell spray foam can go on a stone basement wall once the wall stays dry and the mortar is sound. The foam follows the bumps and hollows of rubble stone and seals air gaps that rigid board would leave open. If the stone is damp or the mortar is crumbling, a mason or waterproofing contractor needs to fix that before we insulate.
No, adding insulation to a basement doesn't need a City of Toronto building permit. Finishing a basement doesn't either, as long as there are no structural or material changes, no new dwelling unit and no new plumbing. A new bathroom, a second suite or a moved structural wall does need one.
Get a Quote
Get a spray foam insulation quote in Toronto
Tell us the address and which part of the house bothers you, whether that is a cold top floor, a drafty basement or a ceiling with no attic above it. Phone or use the form. We'll set up a time to look at the house, then give you a written quote.