Roof insulation in Toronto is a different job when the ceiling has no attic above it, such as a flat-roof addition or a sloped or cathedral ceiling. All you have to work with is the depth of the rafters or joists, and that is usually where spray foam makes sense. Ontario's SB-12 calls this a ceiling without attic space. We insulate these ceilings in older semis and detached houses across the west end.

Ceilings with no attic above them

A ceiling without attic space is any ceiling where the roof deck sits right on the framing you see from below, with no space between them that you could crawl into. The insulation has to fit inside the rafter bays or joist spaces, so depth sets the limit on every one of these jobs.

SB-12 is the energy efficiency standard in Ontario's building code. It sets R-31 as the minimum for a new house's ceiling without attic space in Zone 1, in every compliance package. That rule covers new construction, not an older house you already own. We still use it as a reference when we plan an existing sloped ceiling or flat roof, because it tells you what a new house is built to.

These are the ceilings we mean:

  • Flat-roof additions: the kitchen or back room built onto the rear of the house, where the ceiling joists carry the roof boards too.
  • Sloped ceilings on the top floor, where the room runs up under the roof between short knee walls.
  • Cathedral ceilings, which follow the roof pitch all the way up to the ridge.
  • Dormer roofs. These often have their own small ceiling with nothing above it except the roof deck.

Flat-roof additions at the back of the house

If your house has a flat-roof addition at the back, the joist space above the ceiling is often shallow. Whoever framed those rear additions was thinking about holding up a roof, not about fitting insulation. So flat roof insulation here has very little depth and even less room for air to move, and whatever goes in has to do a lot in a thin layer.

From inside, once the ceiling is open

Once the ceiling is open, our crew sprays closed-cell foam into the joist cavity from inside. The foam sticks to the underside of the roof boards and the sides of the joists, leaving no gap for room air to reach the cold wood. It makes the most sense during a kitchen renovation, or any job where the drywall or plaster is coming down anyway.

From above, when the roof is replaced

When the roof is replaced, rigid insulation board can go on top of the roof deck. The roofer does that as part of the new roof, and nothing inside the room gets touched. Some houses end up with both: board on top at re-roofing, then foam from below during a renovation years later.

Sloped and cathedral ceilings

Cathedral ceiling insulation works the same way as a sloped ceiling. The insulation goes in the rafter bays, the spaces between rafters running from the wall plate up toward the ridge. In older semis the rafters are often shallow and the bays vary in width, and that rules out some materials before we even start.

Closed-cell foam in shallow bays

In a shallow bay, closed-cell spray foam gets you the most insulation for the depth you have. It also acts as an air barrier and slows vapour, so warm room air can't reach the cold roof boards. That's the case where spray foam roof insulation earns its keep: a tight space where nothing else fits well.

Loose-fill or batts with a vent channel

Loose-fill or fibreglass batts can work in a sloped ceiling, but only with a vent channel above them. The channel keeps the insulation off the roof boards and leaves an air path from the soffit to the ridge, so moisture has somewhere to dry out. Skip it and the insulation packs up against the deck and the cavity stays damp.

Knee walls and the flat strip at the top

A lot of top-floor rooms have a sloped ceiling, short knee walls and a small flat ceiling up near the ridge. Behind the knee wall and above that flat strip there's often room for loose-fill, while the slope itself gets foam or a vented assembly. We'd rather match each part to the material that suits it than push one product into all three.

From the inside or during re-roofing

Insulate from inside when the ceiling is coming down anyway, and from above when the roof covering is due for replacement. It comes down to which part of the house gets opened first. Opening a ceiling or stripping a roof just to insulate means paying for work you wouldn't otherwise need.

Permits are simple for most of this. Adding or replacing insulation doesn't need a City of Toronto building permit, though the Zoning Bylaw still applies. Replacing existing roofing material doesn't need one either, as long as there's no structural work.

Here is what usually tips it one way or the other:

  • Go from inside if the roof is sound and the room below is being renovated anyway, say a kitchen ceiling coming down or top-floor plaster being redone.
  • Go from inside if the cavity is shallow and only closed-cell foam will get it to a useful level, since the foam has to be sprayed into an open bay.
  • Wait for re-roofing if the roof covering is near the end of its life and the ceiling finish is in good shape. The roofer adds board above the deck and the room stays as it is.
  • Wait for re-roofing if the ceiling has detail you want to keep, like original plaster or a cove moulding, and you'd rather not have it cut open.

Fix the leak before the foam

A roofer has to repair any roof leak before insulation goes in. Water stains on a sloped ceiling, a soft patch of plaster or damp around a chimney all mean the roof needs looking at first. That repair is a roofer's job. We don't do it.

Foam sprayed over an active leak can hide it. Closed-cell foam sheds water, so a drip that used to show up as a stain on the ceiling can run along the roof boards instead and rot them where nobody sees it. Once the leak is fixed and the wood has dried out, we can insulate.

If older foam went in over a leak, or has pulled away from the framing, it has to come out before the bay can be redone. With spray foam removal we cut it back to the roof boards so the wood can be checked and the cavity insulated properly.

Moisture in roof cavities

Moisture in a roof cavity often comes from inside the house, not from the roof. Warm indoor air carries water vapour. When that air leaks into a cold roof cavity in winter, the vapour condenses on the underside of the roof boards.

After a few winters you can get damp insulation, mould on the sheathing and stains that look like a leak. What matters most here is an airtight insulation layer and a sealed ceiling. Most of the air gets through at pot lights, around a plumbing stack or along the top of a knee wall, so we seal those while we insulate.

We think about the rest of the top floor the same way. If a house has a regular attic as well as a sloped or flat section, we do them as one job, so the attic insulation and the ceiling without attic space get air sealed together. At Premier Insulation Toronto we plan the whole top floor, not one ceiling at a time.

FAQ

Common questions about roof & flat roof insulation

For a roof with no attic above it, closed-cell spray foam is usually the best choice. It gets the most insulation into the shallow depth of the rafters or joists and seals air at the same time. If there's an open attic, loose-fill on the attic floor is normally a better fit. It depends on how much depth the framing gives you and whether the ceiling is open.

Yes, once the ceiling below it is opened. We spray closed-cell foam into the joist space against the underside of the roof boards, then the ceiling gets closed up again. The roof has to be dry and sound before any foam goes in.

The insulation goes in the rafter bays, either as closed-cell spray foam against the roof boards or as loose-fill or batts under a vent channel. Foam suits shallow rafters because it doesn't need an air space above it. Batts and loose-fill need the vent channel so the roof can dry out from the soffit to the ridge.

Yes, where the ceiling has no attic above it and the roof is dry. One layer of closed-cell foam insulates, seals air and keeps warm room air off the cold roof boards. Over a leaking roof it's a poor choice, because it can hide the water until the wood has rotted.

Get a Quote

Get a spray foam insulation quote in Toronto

Tell us the address and which part of the house bothers you, whether that is a cold top floor, a drafty basement or a ceiling with no attic above it. Phone or use the form. We'll set up a time to look at the house, then give you a written quote.

Call Text Quote