Wall insulation in Toronto starts with knowing what your walls are made of. If you have a frame wall with empty stud bays, we can dense-pack it through small holes and patch them afterwards. A solid double-brick wall has no cavity to fill, so the only way in is from the inside, and that takes care. This page is for owners of older houses, whether that's a balloon-framed semi or a solid brick house, who want warmer rooms and fewer drafts.

Start with what the wall is made of

The right method depends on how the wall is built, so the first job is working out what's between your plaster and the outdoors. A few clues can tell you a lot before anyone drills or opens anything up.

  • Look at the brick pattern outside. If every few courses there's a row of bricks laid end-on (these are called headers), those bricks tie two layers together, and you most likely have solid double-brick walls.
  • Check how deep your window and door openings are. A deep jamb with plaster going straight onto the inner face suggests solid masonry. A shallower jamb over a hollow space suggests framing.
  • Knock on the inside wall. Plaster on wood lath over a hollow stud bay sounds different from plaster laid straight onto brick, which sounds dead and solid.
  • Look in the basement or attic where the wall meets the floor framing. If the stud bays run open past the floors, the house is probably balloon framed.

Frame walls behind brick or siding

A wood-frame wall has stud bays behind the plaster or drywall. Those are the hollow spaces between the studs. Brick veneer or siding on the outside is only a skin and isn't what holds the house up. Empty stud bays can be dense-packed from inside or outside, and this is the simplest kind of wall to improve.

Double-brick walls

Here the house is carried by two layers of brick bonded together, with plaster put straight onto the inner face or onto wood strapping. There's no cavity to fill. To insulate it you have to add a layer on the inside, and that changes how the brick dries, so it has to be planned carefully.

Balloon-framed walls

In balloon framing the studs run in one piece from the sill up to the roof, so each stud bay is an open channel past every floor, and air rises through them the way it rises up a chimney. These walls take dense-pack well. The tops and bottoms need blocking or air sealing first, though, or the insulation won't stay put and the draft won't stop.

Dense-pack through small holes

Dense-pack means blowing loose insulation into a closed stud bay under pressure until it's packed tight enough that it won't settle. We drill small holes into each bay, feed a hose in and fill it, then plug and patch the holes. It's the same cellulose or fibreglass used for loose-fill insulation in attics, just packed far harder than it would ever sit on an attic floor.

We can drill from inside or outside. Inside, our crew goes through the plaster or drywall, fills each bay and patches the hole, and you'll need to paint the patches once they dry. On a sided house we can sometimes lift a course of siding and drill behind it, so the rooms aren't touched at all. Brick veneer doesn't drill cleanly, so on those houses we work from inside.

Dense-pack works for frame walls with empty bays, and for balloon-framed walls once their ends are blocked. It doesn't work for bays that already have old insulation in them, bays with blocking we can't get past, or solid brick, which has no bay at all. Before we drill, we check each bay for wiring, blocking and whatever is already in there.

Packing a bay tight also slows air moving through the wall, because dense material holds back air much better than loose fill does. That air sealing counts for as much as the insulation value.

When the walls are already open

Insulating existing walls is much easier during a renovation, once the plaster or drywall is off, because you can see every stud bay and fill it properly. There are two sound ways to do it: spray foam, or batts with a sealed air barrier on the warm side.

Spray foam wall insulation

Spray foam wall insulation goes into open stud bays, fills in around wires, pipes and awkward framing, and seals air leaks at the same time. Closed-cell spray foam is rigid and resists vapour, so it's a good fit for bays against a cold exterior wall. Open-cell foam is softer and lets more moisture through. It's better suited to interior walls and sound control.

Batts with a proper air barrier

Fibreglass or mineral wool batts do a good job when each one is cut to fit its bay and the air barrier on the warm side is sealed at every seam, electrical box and edge. Batts stuffed in around wires or left with gaps lose a lot of their value. We cut around obstacles and tape the barrier so warm, damp indoor air can't get to the cold side of the wall.

Insulating solid brick from inside

Solid double-brick walls can be insulated from inside, but it takes care and it isn't always the right call. In a cold climate, insulating the inside of an older load-bearing brick wall can cause durability problems in some cases. The main ones are freeze-thaw damage to the brick and decay of wood built into the wall. Once the inside is insulated, the brick runs colder and dries more slowly, so any water that gets in does more harm.

We start with water. Before adding anything, we look at where the wall gets wet: window sills that tip toward the wall instead of away from it, failed mortar joints, downspouts emptying against the brick, soil sloping toward the foundation. Fixing the wetting at the window sills and at grade does more to lower the risk than any choice of insulation.

Whatever insulation goes on needs an airtight layer on the inside, so warm indoor air can't leak into the wall and condense on the cold brick. The usual ways to get there are closed-cell foam against the brick or rigid board with every joint sealed, and either way we check the ends of the floor joists set into the brick first. Our page on insulating the walls of an old brick house goes through it room by room.

Exterior wall insulation

Exterior wall insulation means fixing rigid board to the outside of the wall and covering it with new cladding, and for masonry walls it's the easiest, lowest-risk approach. The brick ends up on the warm side, where it stays drier and is much less exposed to freezing.

The catch is usually the facade. Wrapping the outside hides the brick on a Victorian or Edwardian front, makes every window opening deeper and means new cladding over the whole house. We don't do cladding work. We insulate from inside, and you'll find the rest of what we do on the Premier Insulation Toronto home page.

Rebates and permits for wall insulation

Home Renovation Savings lists wall insulation on its home energy assessment route. Read the program's own terms for what it pays and the order the steps have to happen in, and do that before any wall is drilled or opened.

Adding insulation on its own doesn't need a City of Toronto building permit. Material alterations such as adding or removing walls do, so if the same renovation moves or takes out a wall, that part of the job needs a permit before work starts.

More on Wall Insulation

FAQ

Common questions about wall insulation

Yes. If a wall has empty stud bays, we can dense-pack it through small holes without taking off any drywall or plaster. We drill, fill and plug each hole, and you'll need to paint the patches afterwards. Solid brick walls have no bays, so this won't work on them.

For frame and balloon-framed walls with empty bays, yes. Those walls lose heat and leak air, and dense-pack deals with both without gutting the rooms. Solid brick is a closer call, because insulating it from inside carries some risk to the brick and to wood in the wall. We look at the house first and tell you which walls are worth doing.

Yes, a double brick wall can be insulated from the inside, once the wetting at window sills and grade has been dealt with and an airtight layer goes on the inside. Insulating the inside keeps the brick colder, and in some cases that leads to freeze-thaw damage or decay of wood in the wall. Insulating from the outside is less risky, but it means covering the facade with new cladding.

Yes, spray foam is a good choice when the stud bays are open. It fills around wires and framing and air seals at the same time. Closed-cell foam also resists vapour, which helps on cold exterior walls and against brick. You can't spray it into a closed wall, though, so if the plaster is still on, dense-pack is the better method.

Get a Quote

Get a spray foam insulation quote in Toronto

Tell us the address and which part of the house bothers you, whether that is a cold top floor, a drafty basement or a ceiling with no attic above it. Phone or use the form. We'll set up a time to look at the house, then give you a written quote.

Call Text Quote