Open cell spray foam is one of the two kinds of spray foam insulation we use in Toronto homes, and it is the soft, lighter one. It seals air and fills a cavity completely, but vapour passes through it, so it works in some parts of a house and not in others. If you're planning a renovation, this page explains where open-cell belongs and where we keep it out.

What open-cell foam is

Open-cell foam is sprayed on as a liquid and cures soft and spongy. Its tiny cells stay open, so the finished foam is light and gives a little when you press it. It expands fast as it goes on and fills in around wires, pipes and crooked framing, the places where a batt would leave gaps.

Since it fills every corner, open-cell foam works as an air barrier once it is sprayed to full depth. In a century home that matters. Much of the heat escapes through gaps around the framing and wherever pipes and wires pass through, not through the insulation itself.

Open-cell foam is also vapour-open, which means water vapour moves through it. In some assemblies that's fine, and in others it causes trouble. Inch for inch it insulates less than closed-cell, so it needs a deeper cavity to reach the same R-value.

Open cell vs closed cell, point by point

Both foams come out of similar equipment, but once they cure they behave very differently. The open cell vs closed cell choice usually comes down to the points below. For more on the denser foam, see our closed-cell spray foam page.

  • Density: open-cell is soft and light. Closed-cell cures hard and dense.
  • Vapour: open-cell lets vapour through. At full depth, closed-cell slows vapour enough to be its own vapour control.
  • Depth needed: open-cell needs more depth to reach the same R-value, so it goes in deep cavities. Closed-cell does more in a tight space.
  • Water: if a leak reaches open-cell, it soaks the water up like a sponge. Closed-cell sheds it.
  • Where each goes in an older house: open-cell in frame walls and deeper sloped ceilings, closed-cell at rim joists, against brick and below grade.
  • What open-cell is not for: anywhere the foam itself has to stop vapour, like the inside face of masonry or a basement wall.

Where open-cell foam fits

Open-cell foam fits where there is room for depth and the assembly around it can dry out. In an older house, that leaves only a few spots.

Frame wall cavities opened during a renovation

When a wall is stripped to the studs, open cell spray foam insulation fills the cavity from the sheathing out to the face of the studs and seals around electrical boxes and wiring. This is for frame walls, like a rear addition or a framed partition. Double-brick walls are a different case, covered further down.

Deeper sloped ceilings

Sloped ceilings under the roof deck can take open-cell if the rafters are deep enough to give the foam the depth it needs. A shallow slope or a flat roof is a different job, and our roof and flat roof insulation page explains how we handle those.

Interior spots with room for depth

Knee walls and other framed walls facing an unheated space can take open-cell if the framing leaves enough room. If it's too shallow, we use closed-cell.

Where we use closed-cell instead

We switch to closed-cell anywhere the foam has to control vapour on its own. Open-cell would let warm, moist indoor air through to the cold surface behind it, and that cold surface is where water collects. Open-cell should stay out of these places:

  • Against brick or stone: the inside face of a double-brick wall gets cold in winter, and vapour coming through open-cell can condense on it.
  • At rim joists: the rim sits on the foundation, cold and leaky, and it needs a single layer of foam that seals air and controls vapour at the same time.
  • Below grade: basement walls stay damp, and spongy foam pressed against masonry or concrete holds onto that moisture.
  • In shallow cavities: open-cell can't reach a useful R-value without enough depth. Closed-cell does more in the same space.

Indoor humidity and open-cell foam

Open-cell foam lets vapour through, but in thicker layers it can still be a reasonable choice if the house stays at low humidity through the winter. Drier indoor air means less vapour moving into the foam, and less of it reaching a cold surface and turning to water.

Ordinary ventilation does most of the work of keeping winter humidity down. Bathroom fans and the kitchen range hood need to vent outside, not into the attic or a wall cavity. A fan that empties into the attic just moves the moisture to the coldest part of the house.

Before we quote, Premier Insulation Toronto checks where those fans actually end up. If a house runs damp in winter, we move the risky spots to closed-cell, even where open-cell would otherwise fit.

FAQ

Common questions about open-cell spray foam

Open-cell foam is soft and lets vapour through. Closed-cell foam is dense and controls vapour by itself. Open-cell needs more depth for the same R-value, so it suits deep frame cavities, while closed-cell goes where space is tight or where the foam has to stop moisture, such as rim joists and basement walls.

Open cell spray foam is a good choice for frame walls opened to the studs, and usually a poor one for brick or below-grade walls. In a frame cavity it fills around the wiring and seals air leaks. Against cold masonry, vapour can pass through it and condense on the brick, so we normally use closed-cell there.

In most walls and roofs in a cold climate, yes. Open-cell foam lets vapour pass, so it needs separate vapour control. The exact detail depends on the assembly. Where the foam itself has to provide the vapour control, we use closed-cell.

No. Open-cell foam inside a living space has to be covered, and the drywall over it is what gives it fire protection. We trim the cured foam flush with the framing so the drywall sits flat.

The right foam depends on what is behind each wall and how damp the house runs in winter, so we look at the house before quoting. We check the wall type, how deep the cavities are, and where the bath and kitchen fans vent. Plenty of older houses end up with both foams, each one where it suits.

Get a Quote

Get a spray foam insulation quote in Toronto

Tell us the address and which part of the house bothers you, whether that is a cold top floor, a drafty basement or a ceiling with no attic above it. Phone or use the form. We'll set up a time to look at the house, then give you a written quote.

Call Text Quote